Flo

Garbage Disposal Troubleshooting – The Ultimate Guide

Posted on 23/11/2020 by Gabriel Halimi

Garbage disposals are a wonderful modern convenience to have in your kitchen, but like all great gadgets, they can run into problems after repeated uses. Most garbage disposal problems can be fixed without having to call a plumber. In this guide, we’ll go over the “big four” — leaking garbage disposals, disposals that turn on but don’t spin, disposals that won’t turn on at all, and clogs. Finally, we’ll give you a rundown on the things you should never put in your garbage disposal. 

Before we dive in, let’s declare a little golden rule for garbage disposal troubleshooting: keep your hands out of the garbage disposal. Keep this in mind at all times or else you’re going to be googling “garbage disposal injury troubleshooting” next. You can take care of all your garbage disposal issues without putting your limbs at risk. 

Garbage Disposal Is Leaking 

Garbage disposal leaks can have a number of causes, so the first step to troubleshooting this problem is to locate the leak. There are four major areas where leaks happen: the sink flange (where the unit connects to the sink), the inlet hose (the line going to the dishwasher), the drain line (the line going to your drain pipe) and the bottom of the unit. 

If you can’t get a clear look at where the leak is coming from, here’s a little hack you can use. Put a plug in your sink and fill it with a few inches of water. Add some food dye or coloring to the water. Now pull the plug and observe under the sink. Take a look at where the colored water is coming from. 

The Sink Flange

One of the more common causes of garbage disposal leaks is the seal around the sink flange getting knocked loose or degrading over time. If the leak is coming from the area right under the sink, and not one of the hoses along the side of the unit, re-sealing the flange will probably solve your problem. It’s a bit of an involved task. You’ll need a flathead screwdriver and plumber’s putty. 

1. Turn off power supply to disposal unit 

As always, make sure there’s no power going to the unit. That means turning off the switch on the wall and in the circuit box. 

2. Unscrew the flange mount, inlet and outlet lines.

Underneath the sink, you’ll see your disposal unit. There are two screws underneath the flange where the unit attaches to your kitchen sink. There’s also a set of screws mounting the inlet hose (going to your dishwasher) and outlet line (going to your waste pipes). Remove all the screws. Be careful to keep them in a safe place. 

3. Detach the garbage disposal

Free the unit from the sink by twisting the flange. Keep a hand underneath the disposal unit so it doesn’t get damaged when you release it. 

4. Peel off the old putty and reseal 

Once you’ve removed the unit, peel or scrape off any of the old putty around the sink. You have two options to re-seal the area. You can apply new plumber’s putty, or you can purchase a seal that is attached between the sink and flange. 

5. Re-mount the garbage disposal and test 

After you’ve resealed the area, you need to put everything back in its place. Re-mount the unit and replace all the screws you removed in step 2. Once everything’s secure, turn the power supply on and and run your faucet while checking under the sink for leaks. 

The Inlet or Drain Lines

Another common location for garbage disposal leaks is around the inlet (to your dishwasher) or drain lines. This is usually caused by a worn out gasket or loose screws where the lines attach to your garbage disposal unit. Simple examine the connection and check the screws. If they seem tight enough, you’ve probably got a worn out gasket, which can be picked up at most hardware or home improvement stores. 

Bottom of the Unit 

If you’ve got water coming from the bottom of your garbage disposal unit, you’re most likely looking at a full-on replacement. Often leaks will occur around the “reset” switch or the seal near the power supply. These are all caused by cracks or worn out seals inside the unit itself. The cheaper and more convenient option is to just get a brand-new garbage disposal. 

Garbage Disposal is Humming, But Not Spinning 

humming garbage disposal

If you turn on your garbage disposal unit and hear the motor humming but the blades aren’t spinning, the most likely cause is some sort of obstruction in the blades. To troubleshoot this problem, you’re going to attempt to manually get the blades turning to try to knock the obstruction loose. 

1. Turn off power to the unit 

Whenever you’re working on your garbage disposal, turn off the power to the unit. This includes the power switch near the unit and the switch on your circuit board. Safety first.

2. Locate the flywheel turning hole

If you look under the sink where your garbage disposal is, you’ll see the unit motor. At the bottom of the unit there’s a hole shaped like an Allen wrench. Garbage disposals usually include their own flywheel tool, but if you can’t find yours you can use an Allen wrench that fits the hole.

3. Manually rotate the flywheel

Using either the garbage disposal tool or an Allen wrench, manually rotate the flywheel. If there’s a substantial obstruction you’ll probably feel some pretty strong resistance. Just keep alternating the direction you turn the wheel in. Keep doing this and you should feel the obstruction break free. Once you get to the point where you can easily rotate the flywheel, you should be good to go. 

4. Other options 

If you can’t free the flywheel by using a tool, you might be able to remove the obstruction by going into the garbage disposal through the sink. Now, remember the golden rule. Never put your hand in the garbage disposal. Use a flashlight or your phone to look into the disposal. If you can clearly see something stuck in there, you can try removing it with a pair of long, needle-nose pliers.   

Garbage Disposal Won’t Turn On 

If you turn on the garbage disposal and you hear absolutely nothing (no humming or motor sounds), you’re looking at one of the following issues:

  • Your garbage disposal isn’t plugged in.
  • Your garbage disposal needs to be “reset.”
  • The circuit that controls your garbage disposal unit has been shut off. 
  • You have bad wiring on the switch that operates your disposal unit.
  • You need to replace your garbage disposal unit.

We started that list with the most obvious and easy fix, and that’s exactly how you should start troubleshooting the problem. Go down the list and eliminate the possible causes one by one until you either get the unit to work again or start shopping for a new one. 

1. Take care of the easy steps

Let’s eliminate some of the easy stuff first. Take a look under your kitchen sink and you should find the outlet that your garbage disposal unit is plugged into. If it’s unplugged, plug it in. If it’s already plugged in and the unit won’t turn on, look for a little “reset” button on the unit. If it’s sticking out, try pushing it back in.

2. Check your circuit breaker/box

If you weren’t able to get your unit up and running again by going under the sink, it’s time to see if the circuit was tripped. Find your circuit box and locate the circuit that controls your garbage disposal unit. Hopefully you have a circuit box that is labeled, but if it isn’t just look for a switch that is in the OFF position. Once you locate the switch, go ahead and turn it on and go back and test your garbage disposal.

3. Check the switch

If resetting the circuit didn’t solve your problem, there’s one last check you can do before replacing your unit altogether. You’re going to have to test the switch that controls your garbage disposal. Before you start unscrewing the switch cover, make sure the circuit lever is turned off. Make sure this stays off the entire time you’re working on the switch. 

Next, unscrew the cover plate on the switch with a flathead screwdriver. Once the plate is removed, you should see two phillip’s screws. Loosen those screws enough and you’ll be able to pull the switch free from the outlet. Along the side of the switch you’ll see two wires, each secured by its own screw.  

Examine the wires. If any seem like they’re loose or not fully connected, loosen the screws and move the wires into place. If you suspect you have a faulty switch, you can remove the switch completely and test it with a multimeter, or just replace it.  

When you finish, make sure all screws are fully secured. Go ahead and flip the circuit back to the ON position and test out your garbage disposal unit. 

4. Replace the unit

If you’ve managed to get this far, you’ve made sure the garbage disposal unit is plugged in, reset, there’s power going to the unit and the switch operating the unit is good. That can only mean one more thing: your unit is faulty. Either it has damaged wiring or the motor has burn out. Either way, there’s no sense in trying to repair it. You’re going to need to buy a new unit. 

Garbage Disposal Not Draining 

garbage disposal not draining

If your garbage disposal won’t drain, you’ve got a clogged pipe. Some people will assume that the clog is in the unit itself. This is usually not the case. Most of the time, the blockage is in the p-trap (the u-shaped pipe under your sink) or the discharge pipe (the pipe that goes from your disposal unit to your drain pipe).  

Like always, the first step is shutting off all power to the unit. Next, carefully remove the discharge pipe and the p-trap. The trick is to operate very slowly, always having a bucket underneath to catch the water that will inevitably leak out of the pipe fittings. 

Once you have the pieces removed, you should see the obstruction in one or more of the segments. Scrape out all of the solid material and rinse the pieces.  

If you can’t find any sort of obstruction in any of the pipe segments under your sink, you may have a clog somewhere deeper in your plumbing system. In that case, you can use an auger to try to get deeper into the lines, or call in a plumber to deal with the issue.  

Once you’re finished, reattach the p-trap and discharge pipe and test the faucet.

What NOT to Put Down a Garbage Disposal

Garbage disposals are great at taking care of those little scraps of food that are left on your pots, pans and plates. But plenty of homeowners get into the habit of using their garbage disposals and literal trash cans. Putting the wrong things in the disposal will eventually lead to a clog. Not fun. 

Grease, hard materials (bones, shells, pits) and fibrous foods are all things that can cause problems for your garbage disposal. Here are the “big five” things you’re going to want to put in the trash instead. 

1. Cooking grease and oil 

Hot grease or oil might seem completely harmless to your garbage disposal blades, and that’s mostly true. The reason pouring oil down your garbage disposal is a bad idea is what grease does to your pipes. When grease and oil cool down, they become solid. Grease buildup on pipes is a common thing that can lead to clogs and even leaks down the road. 

2. Coffee grounds

There are plenty of organic food items that are perfectly fine for your garbage disposal. Unfortunately, coffee grounds aren’t one of them. Coffee grounds have a habit of caking together and forming blockages, especially at the p-trap below your kitchen sink. Put coffee grounds in the trash instead.  

3. Pasta, rice and other grains 

Grains are bad for your pipes because they expand in water. If the grains don’t make it all the way out of your drain system, they’ll most likely end up clogging up your p-trap and giving you some serious plumbing headaches. It’s probably unavoidable to put some grains down the drain, but try your best to get most of them into the garbage can.  

4. Bones

Garbage disposal blades are tough, but they can’t handle everything. Bones are way too dense to be chopped up by your disposal blades and are more likely to get caught and jam up your unit’s flywheel.

5. Eggshells

Eggshells are definitely brittle enough to get ground up by your garbage disposal, but they still pose some problems. Eggshells have little membranes that can get caught up in your disposal unit, which can lead to mechanical problems and even clog pipes further down your plumbing system.  

Wrapping It Up 

As you can see, most garbage disposal problems can be easily fixed with some common household tools and a little work. There’s always a few things you can try before you call up your plumber. Then there’s the homeowner’s most powerful tool: preventative maintenance. Being mindful of what you put in your disposal can help you avoid clogs.

Articles You May Like

How to Prepare Your Home for a Power Outage

In this article, we’ll give you 11 tips to prepare for and navigate a power outage. 

Read More
Publié par Gabriel Halimi le
How to Save Money on Leak Detection? Get your Insurance to Help Pay for It

There are lots of ways to save money on leak detection. Our recommendation? Let your insurance company pay for it. 

Read More
Publié par Gabriel Halimi le
Smart Home Market Declines as Homeowners Look for Integration to Connect their Smart Devices

What smart ecosystem are you building in your home?

Read More
Publié par Gabriel Halimi le
The Story of Flo

Say hello to the father and son team behind the Flo by Moen Smart Home Water Security System! 

Read More
Publié par Gabriel Halimi le
5 Crucial Ways to Protect Your Home When You’re Gone
Here are a few ways to hack your home to make sure it’s safe, protected, and vacation-ready.
Read More
Publié par Gabriel Halimi le
How to Prevent Mold and Mildew
Make sure to put these practices into place to prevent mildew and mold growth to keep your home and your loved ones safe.
Read More
Publié par Gabriel Halimi le
6 Money-Saving Tips for Airbnb Hosts
Here are six foolproof tips from Airbnb superhosts to maximize your profits and keep your Airbnb in the black.
Read More
Publié par Gabriel Halimi le
How to Ensure Your Vacation Home Isn’t Wasting Water When You’re Away
Here are a few tips to make sure your vacation home is secured even after you leave.
Read More
Publié par Gabriel Halimi le
How to Unclog Your Bathtub Once and For All
Read More
Publié par Gabriel Halimi le
Your Toilet Could Be Leaking Right Now
We use our toilets every day, yet to most of us, they remain a mystery.
Read More
Publié par Gabriel Halimi le
How to Find Leaks in Your Home
Small leaks are a big deal. The stealthy damage leads to costly repair bills. Here's how you can find water leaks behind walls and ceilings.
Read More
Publié par Gabriel Halimi le
7 Ways You Can Help the Environment at Home
Learn about the countless ways to help the environment from home. Some require nothing more than keeping a conscientious eye on your energy usage.
Read More
Publié par Gabriel Halimi le
Waiting For Frozen Pipes To Thaw? What To Do Instead
Every minute you have ice blocking you pipes you’re at risk for a pipe burst. Here's how you can thaw frozen pipes immediately.
Read More
Publié par Gabriel Halimi le
How to Adjust Your Water Pressure Regulator
Here's everything you need to know about adjusting pressure regulator valves so you can tweak your home’s water pressure to your liking.
Read More
Publié par Gabriel Halimi le
Why a Smart Home is a Smart Investment

Will a smart home pay for itself in the long run? Will it simplify your life or complicate it? Read on to see how you may benefit with Flo by Moen.

Read More
Publié par Gabriel Halimi le
How to Find and Repair Water Leaks – A Comprehensive Guide
Learn about water leaks around your home, how to find them and what you can do about it, plus when it is best to call your insurance company or local plumber.
Read More
Publié par Gabriel Halimi le
Sump Pumps – Usage, Installation, and Troubleshooting

In this article, we’ll explain how sump pumps work and give you some basic maintenance tips to keep your pump running for years to come.

Read More
Publié par Gabriel Halimi le
5 Ways To Extend The Life of Your Water Heater
Water heaters don't last forever. But if you follow the maintenance tips in this article, you can expect 10 years from yours.
Read More
Publié par Gabriel Halimi le
Plunger Won’t Work? 5 Ways To Dissolve Waste From Pipe Walls
Sometimes, the plunger just won’t do the trick. That’s why we’ve gathered a few alternatives you can try for stubborn toilet clogs.
Read More
Publié par Gabriel Halimi le
10 Tips for Finding Small Water Leaks at Home

But small leaks are a big deal. Here are a couple of reasons you should be paying attention to small leaks.

Read More
Publié par Gabriel Halimi le
What To Do About Roots In Your Pipes (Without Killing the Tree)

Find out how tree roots make their way into your pipes and how to get rid of them without doing harm to the tree itself.

Read More
Publié par Gabriel Halimi le
10 Easy Ways to Unclog Your Drains

There are plenty of DIY methods to unclog a drain, but it’s not always clear which method is appropriate for your home’s plumbing.

Read More
Publié par Gabriel Halimi le
What to Do When a Pipe Bursts (and Before the Plumber Gets There)
Read about the first steps you need to take when a pipe bursts. Also learn how you can reduce damage and prevent future accidents.
Read More
Publié par Gabriel Halimi le
Everything You Need to Know About Pressure Reducing Valves

In this guide, you’ll learn how water pressure reducing valves work and why they’re such an important part of your plumbing system.

Read More
Publié par Gabriel Halimi le
10 Best Practices to Hurricane Proof Your Home
There’s plenty you can do to protect your property from natural disasters.
Read More
Publié par Gabriel Halimi le
Plumbing Tools List – Everything You’ll Need for DIY Projects
Here’s a list of the essential tools for any DIY plumber.
Read More
Publié par Gabriel Halimi le
How to Clear a Clogged Sewer Line
There’s nothing more chilling than the though of dirty sewage backing up into your home.
Read More
Publié par Gabriel Halimi le